CPU Support |
Support Dual-Core Intel® Xeon® processor 5100 series and Quad-Core Intel®
Xeon® Processor 5300 series (80W)
Intel® Embedded Processor List ( Intel® Longevity CPU):
Dual-Core Intel® Xeon® Processor (5130 & 5140)
Dual-Core Intel® Xeon® Processor LV (5128, 5138, 5148)
1066/1333 MHz FSB support |
System Memory |
4 x 240-pin four channel DDR 2 FB-DIMM
Support ECC / Register DDR2 memory up to 8GB |
BIOS |
AMI BIOS
Plug & Play support
8M-bit flash ROM
Support Soft off, Wake on LAN, Power On by PS2 Keyboard Function Key, RTC
alarm Power On
Power on after power failure |
Chipsets |
Intel® 5000P memory controller Hub
Intel® 6321ESB I/O controller Hub |
LAN |
2 x Intel® 82573L PCI Express Gigabit Ethernet
Support Boot From LAN (PXE)
Support Wake On LAN (When 5Vsb power available)
2 x RJ45 with LED |
Display |
ATI ES1000 PCI graphic Controller
32MB DDR2 SDRAM VGA Memory
1 x DB15 VGA port |
On-Board Super I/O |
- USB 2.0: 4 ports through I/O bracket
- USB 2.0: 2 ports, with 1x6 JST (2.5mm )
- Serial port: 2 ports, with 2x5 box-header (2.0mm) support RS-232 only
- Parallel port: 1 port , with 2x13 box-header (2.0mm), Bi-directional, EPP/ECP
- PS/2: 1 x Mini-Din Keyboard/Mouse
- GPIO: Support 4 sets of general purpose I/O each with TTL level (5V) interface
- FAN: 2 x 4-pin FAN connectors (for CPU coolers)
- 1 x on board buzzer
- 1 x 2-pin power on switch
- 1 x SMBus 2.0 to Backplane
- 1 x 2-pin header for reset
- 1 x 5-pin header for key lock
- 1 x 2-pin header for power LED
- 1 x 2-pin header for HDD LED
|
Storage |
SATA: 2 ports, support RAID 0,1 through Backplane
IDE: 1 x 40-pin IDE connector, support Ultra ATA 33/66/100
1 x 2-pin JST (2.5mm) power connector for DOM (Disk On Module) |
System Monitor |
8 voltage (For +3.3V, +5V, Vcore x2, 1.8V, 1.5V, 5Vsb, and Vbattery)
3 temperature (For 2 CPU and system)
3 FAN speed monitor ( 2 for CPU and 1 for ESB2) |
Watchdog Timer |
Watchdog Timer is programmable by software from 0 to 255 seconds (Tolerance
10% under room temperature 25°C) |
On-Board RTC |
On-chip RTC with battery back up
1 x External Li-Lon battery |
Power Input |
Power source from backplane through PICMG 1.3 Golden Finger, support ATX mode |
Dimensions |
PICMG 1.3 SHB
338.58 mm (L) x 126.39 mm (W) (13.3" x 4.9") |
Environment |
Operating Temperature: 0°C ~ 60°C (for Board Level Only)
Storage Temperature: -20˚C to 85˚C
Relative Humidity:
Operating: 10%~90% (non-condensing)
Non-Operating: 5%~95% (non-condensing) |
Certification |
CE approval, FCC Class A |
